Trim Entities in SolidWorks: Power Trim, Corner, and More

Master trim entities in SolidWorks to clean up sketches fast. See how each trim option works, when to extend instead, and how to trim surfaces.

When you’re creating sketches often will sketch entities such as lines, arcs, circles and others that extend farther than you need.

In this situation you can either delete these entities and redraw the sketch again, but in many cases there is a much faster solution.

There’s command Trim Entities that allows you to remove portions of the sketch that you don’t want while keeping parts of the sketch you want.

Trim Entities command also provides many different trimming options that depend on the typo of the edit you want to make.

In this article we will show how the Trim command works and when to use each option.

Where to Find Trim Entities in SOLIDWORKS

To find the Trim command open or create a sketch and then go to Sketch tab and there you will find Trim Entities.

When Trim command is active, the PropertyManager provides few options: Power Trim, Corner, Trim Away Inside, Trim Away Outside, and Trim to Closest.

Each of these options modify existing sketch geometry, but works slightly differently.

Power Trim

The first one is Power Trim. This is one of the fastest and most flexible to clean up the sketch.

With Power Trim you can click and drag your cursor across multiple entities instead of selecting every sketch segment individually.

So any sketch segment that you cross with the cursor will be trimmed.

For example, when several lines extend through the profile you want to create, instead of deleting lines fully, you just drag Power Trim across unwanted portions.

Now SolidWorks will remove the selected section while keeping the remaining geometry.

Power Trim is useful when working when sketches contain overlapping and intersecting entities.

How to Use Power Trim

Start editing the sketch and select Trim Entities. Select Power Trim from the Property Manager.

Then:

  1. Click and hold the left mouse button.

  1. Drag the cursor across the sketch.

  1. Cross the portions of geometry you want to remove.

  1. Release the mouse button when finished.

While you move the cursor through the sketch, SolidWorks trims entities crossed your cursor.

And this is way faster than selecting and deleting each sketch individually.

 

Corner

Corner Trim option is very useful when you have two sketch entities that must meet at the common corner.

For example, two lines almost intersect but are too short of each other or they cross each other. In this case you can manually extend both lines till they meet, but with Corner option this is done faster and automatically.

Choose Corner in the PropertyManager and then select two entities. SolidWorks will extend or trim selected entities so they meet at their intersection.

So this command can do two operations depending on the geometry:

Extend entities that are too short.

Or:

Trim entities that extend beyond the required corner.

You can use this option when creating profiles made from intersecting lines where you want to quickly make clean corners. 

This option is especially useful when creating profiles made from intersecting lines where you want to quickly establish clean corners.

Trim Away Inside

When you want to remove geometry only within a specific area then use the Trim Away Inside option.

To use this option you have to select two sketch entities that define the boundaries of the trimming area. Then select the geometry within these boundaries to remove it.

For example, we have two vertical lines that are crossing several horizontal entities.

Those vertical lines are boundaries.

And now with Trim Away Inside remove portions located between two vertical lines while you keep the geometry outside the boundaries.

Trim Away Outside

With Trim Away Outside trims the opposite.

Instead of trimming portions that are inside of the two vertical boundaries, it trims the portions outside the boundaries.

In the same example, select two vertical lines as boundaries, and then by trimming portions outside the boundaries will be removed.

 

 

So the difference is this:

Trim Away Inside → removes geometry inside the selected boundaries

Trim Away Outside → removes geometry outside the selected boundaries

Use these two options when you need precise control over which portions of the sketch remain and which one is trimmed.

Trim to Closest

Trim to Closest is useful when you want more precise control over the individual sketch entities.

So instead of dragging the cursor across several entities, just select the portions you want to remove.

And then SolidWorks trims the entity back to the nearest intersecting sketch geometry.

For example, when a horizontal line passes through two vertical lines, clicking one section of the horizontal line removes that specific portion while leaving the remaining sketch intact.

This is very useful in detailed sketches where Power Trim could accidentally cross and remove nearby geometry.

 

 

For quick cleanup involving many entities, Power Trim is usually more efficient.

For individual corrections, Trim to Closest often provides better control.

Working With Construction Geometry

In the PropertyManager at the bottom there is an option that controls how trimmed and  construction geometry are handled.

The first option is Keep trimmed entities as construction geometry.

When this option is enabled, the trimmed geometry is not trimmed but it turned into construction geometry.

This is useful when you don’t need an entity as a part of the actual profile but you want to use it as a reference.

The second option is Ignore trimming of construction geometry.

When this option is enabled, construction geometry is protected from the trimming operation.

This is very helpful

When enabled, construction geometry is protected from the trimming operation.

This can be helpful in sketches containing centerlines or other reference geometry that you do not want to accidentally modify while using Power Trim.

 

Choosing the Right Trim Option

The different Trim Entities options are designed for different situations.

Use Power Trim when you want to quickly remove multiple unwanted sketch segments.

Use Corner when two entities need to meet at a clean intersection.

Use Trim Away Inside when you want to remove geometry within selected boundaries.

Use Trim Away Outside when you want to preserve the geometry between boundaries and remove what extends beyond them.

Use Trim to Closest when you want precise control over individual sketch segments.

When you become familiar with these options, trimming becomes much faster than only deleting and recreating sketch geometry.

Frequently Asked Questions

1. Does trimming an entity delete its dimensions and relations?


Sometimes this can happen.

It depends whether the portion that’s been deleted has been used to define a certain relation.

That’s why it is always good to check whether that’s true and then maybe use a different way to create a sketch.

2. Can I recover a sketch entity after accidentally trimming it?


Yes, you can do this by immediately pressing Ctrl+Z, and this way you undo the Trim operation.

3. Can I trim construction geometry in SOLIDWORKS?


Yes, you can also trim construction geometry.

But also the tool itself has options on how to control construction geometry when trimming.

You can ignore it or include it in the trimming.

Summary

SolidWorks Trim Command is a tool that can significantly speed up the sketching process.

Instead of rebuilding geometry, you can trim unwanted portion while keeping the geometry you need.

For everyday sketching, Power Trim will in most cases be the quickest option.

If you want more controlled edits, then tools such as Trim to Closest, Corner, Trim Away Inside, and Trim Away Outside will give you more flexibility.

Learning when to use each option makes it easier to create cleaner sketches and modify existing geometry without unnecessary redraw work.

By Alen Oletic

Keep reading

  • How to Export STL from SolidWorks and Fusion 360 for 3D Printing
  • SolidWorks vs Fusion 360 which one should you learn
  • How to Create Threads in SolidWorks 3 Methods Best Practices
  • All about SolidWorks CSWA and CSWP certification exams
  • Best SolidWorks courses
  • How to Convert STL to SolidWorks (4 methods)